Toro 38062 Toro 622 38062 Snowthrower Owners Manual, 1999 - 1 of 28
Toro 38062 Toro 622 38062 Snowthrower Parts Catalog, 1999 - 1 of 16
Toro 38062 Toro 622 38062 Snowthrower Drive Systems, 1999 - 1 of 54
From inside (document excerpt):
FORM NO. 3321687 622 Power Throwt Snowthrower Model No. 38062–9900001 & Up Operator’s Manual WARNING: The engine exhaust from this product contains chemicals known to the State of California to cause cancer, birth defects, or other reproductive harm. Figures 1 1 4 3 2 1 m-2592 1. Model and serial number decal 2 1 648 1. Speed selector arm 2. Speed selector rod 3. Flat washer and cotter pin 5 3 2 653 3 1 4 1. Handle 2. Capscrews and curved washers 3. Axle pin 2 4 3 3 1 1. Traction rod 2. Loop 3.
Lower traction rod 4. Flange nuts 654 2 1. Axle pin 2. Outer axle hole 473 3. Inner axle hole and wheel hub EThe Toro Company 1998 Printed in USA Jam nut 2. Clevis 3. Upper control rod 4. Lower control rod 5. Clevis pin 6. Cotter pin 1. Auger control lever 2. Traction control lever 3. Speed selector 4. Speed selector rod 9 7 1 APPROXIMATELY 4-3/8 INCHES APPROXIMATELY FOUR INCHES 1 1 TO 2 INCHES ONE TO TWO INCHES 2 1. Traction control lever 2. Handgrip 665 2 1. Auger control lever 2. Hand grip 665 ii 10 2 12 2 6 8 1 7 886 3 1. chute control bracket and rod 2. Capscrew and locknut 1. 2. 3. 4. Chute Deflector Carriage bolt Rubber washer 1 4 5. 6. 7. 8. 5 667 11 1 Friction plate Large flat washer Curved washer Locknut 13 3 3 2 1 2 658 1. Worm gear and bracket 2. Bolt, pyramidal washer and locknut 3. Mounting flange 1. Filler hole 2. Dipstick 3. Fuel tank cap 684 iii 14 1 3 2 16 3 1 4 6 2 5 879 724 1. Carburetor heater box 2. Phillips screws 3. Hex head screw 1. Auger drive control 2. Traction control 3. Speed selector 4. Discharge chute control 5. Fuel shutoff valve 6. Chute deflector handle 17 3 15 1 2 1 1. Skid 2. Auger side plate 3. Flange nuts 2 651 5 3 1. Choke 2. Primer 3. Throttle 4. Recoil starter 5. Ignition switch 4 725 18 3 2 2 m-3392 1 3. Auger blades 1. Scraper 2. Mounting screws iv 19 2 22 3 1 726 1 1. Drain plug m4070 1. Fuel shut-off valve 2. Hose clamp 3. Fuel line 23 20 1 m-3392 m2592 1 1. Pipe plug 1. Screws 21 887 v 24 25 1 6 3 5 2 1 4 2 664 661 1. Belt cover 2. Screw (2) 1. 2. 3. 4. Traction drive belt Auger/impeller drive belt Belt guide Idler pulley 5. Large auger/impeller pulley 6. Engine pulley 26 1 2 1. Spring 2. Notch in side plate 3 650 3. Large traction pulley vi 27 2 29 1 1 724 1. Spark plug wire 659 1. Flange nuts 2. Speed selector plate 30 28 0.30 ” (0.76 mm) 110 1 2 !/8 ” 650/913 1. Roll pin 2. Drive assembly vii Contents Introduction Safety . Before Operating While Operating . Maintaining Snowthrower . Safety Decals and Instructions Loose Parts . Accessories Assembly Install Handle . Install Speed Selector Rod . Install Traction Rod Install Auger/Impeller Drive Control Linkage 9 Install Chute Control Rod . 9 Secure Chute Deflector . 9 Check Tire Pressure 9 Before Starting 10 Fill Crankcase With Oil . 10 Fill Fuel Tank With Gasoline . 10 Operation 11 Controls . 11 Starting/Stopping 11 Snowthrowing Tips 12 Adjusting Skids And Scraper Blade . 13 Maintenance 14 Draining Gasoline . 14 Lubricating Snowthrower . 15 Changing Crankcase Oil 15 Auger Gear Box Grease . 15 Adjusting Auger/Impeller Drive Belt 15 Replacing Auger/Impeller Drive Belt 16 Replacing Traction Drive Belt 16 Adjusting Traction Drive 17 Adjusting Speed Selector 17 Replacing Spark Plug . 17 Preparing Snowthrower For Storage . 17 Warranty Back Cover Page 1 2 2 3 4 6 7 7 8 8 8 8 Introduction Thank you for purchasing a Toro product. All of us at Toro want you to be completely satisfied with your new product, so feel free to contact your local Authorized Service Dealer for help with service, genuine Toro parts, or other information you may require. Whenever you contact your Authorized Service Dealer or the factory, always know the model and serial numbers of your product. These numbers will help the Service Dealer or Service Representative provide exact information about your specific product. You will find the model and serial number decal located in a unique place on the product (Fig. 1). For your convenience, write the product model and serial numbers in the space below. Model No: Serial No. Read this manual carefully to learn how to operate and maintain your product correctly. Reading this manual will help you and others avoid personal injury and damage to the product. Although Toro designs, produces and markets safe, state-of-the-art products, you are responsible for using the product properly and safely. You are also responsible for training persons who you allow to use the product about safe operation. The Toro warning system in this manual identifies potential hazards and has special safety messages that help you and others avoid personal injury, even death. DANGER, WARNING and CAUTION are signal words used to identify the level of hazard. However, regardless of the hazard, be extremely careful. DANGER signals an extreme hazard that will cause serious injury or death if the recommended precautions are not followed.