Toro Owners Manual - Enlarge page 1 of 2
2 of 2
From inside (document excerpt):
Greensmaster 3150-Q Specifications* ® GREENSMASTER 3150-Q, MODEL 04357 ENGINE FUEL CAPACITY TRACTION DRIVE GROUND SPEED TURF COMPACTION IMPLEMENT DRIVE STEERING ELECTRICAL FEATURES CONTROLS/GAUGES TIRES/WHEELS/ PRESSURE BRAKES HYDRAULIC OIL LEAK DETECTION SOUND LEVEL OVERALL DIMENSIONS WIDTH OF CUT REEL SPEED BACKLAPPING CUTTING UNIT SUSPENSION OPTIONAL ACCESSORIES WARRANTY 18 hp (13 4 kW) Briggs & Stratton gasoline engine, governed to 2850 rpm high idle, 1650 rpm low idle Air cooled, 34 8 cu in (570 cc) ® 7 gallon (26 5 liter) capacity; unleaded gasoline 2 or 3WD w/ROPS, hydrostatic piston pump closed loop system Foot pedal forward and reverse; infinitely variable Forward-mowing speed is variable from 2-5 mph (3 2-8 km/h), adjusted by stop on pedal mechanism Mow speed setting does not affect transport speed Maximum Greensmaster 3150-Q transport speed is 8 8 mph (14 4 km/h), may be reduced by adjusting stop in footrest pan without affecting mow speeds Reverse is 2 5 mph (4 0 km/h) maximum 8-10 psi (dependent on tire pressure) with operator and cutting units down Single gear pump, mono valve block, series reel drive to 3 reel motors Power steering Adjustable steering wheel tilt and a 5-position steering arm tilt 12-volt lead acid, group size U1, with 300 minimum cold cranking amps at 0° F and 34 minutes reserve capacity at 85° F/25 amps draw 16 amp alternator Ignition switch/key Seat switch Harness terminals and fuse slot available for optional lights installation Raise/lower-mow lever (joystick) Functional control lever (neutral, mow, transport) Foot operated traction drive and brakes Hour meter Hand operated throttle and choke Mechanical engine speed control Three tires: 18 x 9 50-8, 2-ply pneumatic, tubeless, demountable and interchangeable with smooth tread Tire pressure: 8-12 psi (55-83 kPa) Optional Traction Tire (2-ply): P/N 231-127 Two 6 ” (15 2 cm) drum type 7 5 gallon (28 4 liter) tank with internal baffle 1 0 gallon (3 8 liter) auxiliary tank Equipped with Turf GuardianTM leak detection system 81 dB(A) at operator’s ear under normal conditions Wheel Tread: 49 5 ” (149 9 cm), Wheel Base: 47 ” (119 cm), Length: 90 ” (229 cm), Width: 69 75 ” (177 cm) w/reels, Height: 48 5 ” (123 cm), Weight (no reels): 970 lbs (440 kg) 59 ” (150 cm) Approximately 1975 RPM at 2850 engine RPM Adjustable Standard equipment Cutting units are completely free-floating, each attaching to the tractor by direct pull links and lifted by a centered lift arm Baskets are supported by carrier frames that are ground following Cutting unit floatation is unaffected by basket content Grass baskets are all interchangeable and accessible from the front of the machine 3WD kit w/ROPS, traction tire, thatching reels, spiker, tri-roller, turf evaluator Two-year limited warranty Refer to the Operator’s Manual for further details Briggs & Stratton provides a two-year commercial engine, and a lifetime Magnetron ignition warranty ® 8 BLADE DPA CUTTING UNITS, 04610 11-BLADE DPA CUTTING UNITS, 04611 14-BLADE CUTTING UNITS, 04616** TRACTOR HEIGHT OF CUT (HOC) RANGE REEL WELDMENT REEL BEARINGS MAINTENANCE REEL DRIVE FRAME AGGRESSIVENESS BEDKNIFE BEDKNIFE ADjUSTMENT FRONT & REAR ROLLERS GRASS SHIELD TOTAL WEIGHT These cutting units will mount on any Toro riding Greensmaster Cutting height is adjusted on front roller by two vertical screws and held by two locking cap screws Bench HOC range is 062 “- 297 ” (1 6-7 5 mm) With high HOC kit, range is 285-1 ” (7 3-25 4 mm) Effective HOC may vary depending on turf conditions and bedknife installed Reels are 5 ” (13 cm) in diameter, 21 ” (53 3 cm) in length High carbon steel blades are welded to 5 stamped steel spiders, and heat treated to RC 48-54 hardness The reel is ground for diameter and concentricity, and backgrind Two double row, self-aligning ball bearings, 30 +/- 1 mm inside diameter slip fit onto reel shaft with lock nut Multiple seal barriers on both sides of bearing for added protection Reel position maintained by a wave washer with no adjusting nut No grease zerks, sealed bearing design eliminates daily maintenance The reel weldment shaft is a 1 375 ” (35 mm) diameter tube with drive inserts permanently pressed in both ends A replaceable floating coupler with an internal eight tooth spline is factory installed on the right end, and held in place by a snap ring The floating coupler may be moved to the other end when the cutting unit is used on the GR3250-D front right position Precision machined, die-cast aluminum cross member with two bolt-on die-cast aluminum side plates Aggressiveness stays constant throughout the life of the reel Patented design Replaceable single edged, high carbon steel bedknife austempered to RC 48-55, fastened to a machined cast iron bedbar with 13 screws Tournament Bedknife is standard on 8-blade & 11-blade cutting units EdgeMax Microcut Bedknife is standard on 14-blade cutting unit TM Dual screw, indexed “click ” adjustment to the reel; detents corresponding positively to 0007 ” ( 018 mm) bedknife movement for each position Front: Aluminum Wiehle , 2 5 ” (6 4 cm) diameter with sealed bearings and through-shaft Option between full, narrow-spaced and wide-spaced roller Rear: Steel full, 2 ” (5 1 cm) diameter with sealed bearings and through-shaft ® Non-adjustable shield with adjustable cut-off bar to improve grass discharge from reel in wet conditions 8-blade: 72 lbs (32 7 kg) with aluminum Wiehle Roller 11-blade: 75 lbs (34 1 kg) with aluminum Wiehle Roller *Specifications and design subject to change without notice **Available Winter/Spring 2010, see your distributor for details The Greensmaster 3150-Q is manufactured in Tomah, WI ISO 9002 Certified Plant 45 Greensmaster 3150-Q Specifications* (continued) ® GREENSMASTER 3150-Q ACCESSORIES TRACTION UNIT ACCESSORIES 04474 04496 04494 04495 106-6392 106-5422 95-5943 30707 231-127 105-8258 108-6472 105-8336 112-9177 105-8339 3-Wheel Drive Kit Thatching Reel Kit Greens Spiker Kit Greens Tri-Roller Kit Re …..