Toro Owners Manual - 1 of 2
Toro Owners Manual - 2 of 2
From inside (document excerpt):
Greensmaster 3250-D Specifications* ® GREENSMASTER 3250-D, MODEL 04383 ENGINE FUEL CAPACITY TRACTION DRIVE GROUND SPEED TURF COMPACTION STEERING CONTROLS/GAUGES ELECTRICAL FEATURES SOUND LEVEL Briggs and Stratton /Daihatsu 850D tier 4 3-cylinder liquid-cooled diesel engine 51 9 cu in (850 cc) Full pressure lubrication, oil filter 21 0 hp (15 7 kW) at 3600 rpm, 16 +/- 5 hp (11 9 kW) at 2600 rpm Engine governed to 2925 rpm high idle, 1500 rpm low idle (no load) ® ® 6 gallons (22 7 liters) 2008 models Biodiesel-Ready for use up to B-20 (20% biodiesel and 80% petrol blend) Hydrostatic piston pump, closed loop system Foot pedal forward and reverse; infinitely variable Two front wheel orbit motors, 10 3 cu in/rev displacement 2 or 3 WD with ROPS Forward-mowing speed is variable from 2-5 mph (3 2-8 km/h), adjusted by stop on pedal mechanism Mow speed setting does not affect transport speed Maximum Greensmaster 3250-D transport speed is 8 8 mph (14 4 km/h), may be reduced by adjusting stop in footrest pan without affecting mow speeds Reverse is 2 5 mph (4 0 km/h) maximum 10 psi ( 68 bar) average at recommended minimum tire pressures, with a 200 lb operator, and cutting units down Power steering Open center, non-load reacting steering valve with power beyond for raise/lower circuit and hydrostat charge circuit 13 0 ” (33 cm) round steering wheel No-tool quick adjust steering arm position, with arm motion allowing a wide range of operator sizes Steering cylinder has 1 50 ” bore x 6 25 ” stroke with through shaft design for accurate straight line steering Raise/lower-mow lever Functional control lever (neutral, mow, transport) Foot operated traction drive and brakes Hour meter and 4 bulb warning cluster Hand operated choke, throttle Mechanical engine speed control Water in fuel warning light Maintenance-free 12-volt battery with 530 minimum cold cranking amps at 0° F (-17 7° C) and 85 minutes minimum reserve capacity at 85° F (29 4° C) 40 amp alternator, circuit fused at 40 amps Ignition switch/key Seat switch High temperature engine kill override switch Harness terminals, fuse slot, and console switch location available for optional lights installation GR3250-D Reels Off Reels On Width of Cut: Wheel Tread: Wheel Base: Overall Length (w/baskets): Overall Width: Operator Ear 83 dBA 84 dBA 59 0 ” (150 cm) 50 5 ” (128 cm) 48 6 ” (123 cm) 93 9 ” (238 cm) 68 0 ” (173 cm) At 25′ 73 dBA Overall Height: Net Weight (no fuel, no operator): Reel Speed: At 75′ 62 dBA 50 5 ” (128 cm) 1,108 lbs (503 kg) 1950 rpm minimum (Adj) OVERALL DIMENSIONS TIRES LEAK DETECTION BACKLAPPING BRAKES SEAT OPTIONAL ACCESSORIES CERTIFICATION WARRANTY Three 19 x 10 5-8, 2 ply pneumatic tubeless demountable and interchangeable Smooth tread (approx 1290 rev/mile) 8-12 psi front; 8-15 psi rear Turf GuardianTM optional Standard equipment 6 ” (15 2 cm) drum type mechanical with rack and pawl lock for parking Contour seat with high backrest 7 ” (17 8 cm) fore/aft slider adjustment with two mounting positions, allowing 9 ” (22 8 cm) total seat travel Operator manual tube mounted on the seat back for easy access ROPS, 3WD kit, traction tire, thatching reels, spiker, tri-roller, turf evaluator, quiet muffler kit, armrest kit, leak detector kit, hose adapter kit, light kit, oil cooler kit, radiator screen kit, ground-following suspension kit, 19 ” wheel weight kit, 400 hour maintenance kit Certified to meet ANSI specification B71 4-2004 and European CE standards Two-year limited warranty Refer to the Operator’s Manual for further details Briggs & Stratton provides a two-year commercial engine, and a lifetime Magnetron ignition warranty ® *Specifications and design subject to change without notice 48 Greensmaster 3250-D Specifications* (continued) ® 8 BLADE DPA CUTTING UNITS, 04610 11-BLADE DPA CUTTING UNITS, 04611 14-BLADE CUTTING UNITS, 04616** TRACTOR HEIGHT OF CUT (HOC) RANGE REEL WELDMENT REEL BEARINGS MAINTENANCE REEL DRIVE FRAME AGGRESSIVENESS BEDKNIFE BEDKNIFE ADjUSTMENT FRONT & REAR ROLLERS GRASS SHIELD TOTAL WEIGHT These cutting units will mount on any Toro riding Greensmaster Cutting height is adjusted on front roller by two vertical screws and held by two locking cap screws Bench HOC range is 062 “- 297 ” (1 6-7 5 mm) With high HOC kit, range is 285-1 ” (7 3-25 4 mm) Effective HOC may vary depending on turf conditions and bedknife installed Reels are 5 ” (13 cm) in diameter, 21 ” (53 3 cm) in length High carbon steel blades are welded to 5 stamped steel spiders, and heat treated to RC 48-54 hardness The reel is ground for diameter and concentricity, and backgrind Two double row, self-aligning ball bearings, 30 +/- 1 mm inside diameter slip fit onto reel shaft with lock nut Multiple seal barriers on both sides of bearing for added protection Reel position maintained by a wave washer with no adjusting nut No grease zerks, sealed bearing design eliminates daily maintenance The reel weldment shaft is a 1 375 ” (35 mm) diameter tube with drive inserts permanently pressed in both ends A replaceable floating coupler with an internal eight tooth spline is factory installed on the right end, and held in place by a snap ring The floating coupler may be moved to the other end when the cutting unit is used on the GR3250-D front right position Precision machined, die-cast aluminum cross member with two bolt-on die-cast aluminum side plates Aggressiveness stays constant throughout the life of the reel Patented design Replaceable single edged, high carbon steel bedknife austempered to RC 48-55, fastened to a machined cast iron bedbar with 13 screws Tournament bedknife is standard on 8-blade & 11-blade cutting units EdgeMax Microcut Bedknife is standard on 14-blade cutting unit TM Dual screw, indexed “click ” adjustment to the reel; detents corresponding positively to 0007 ” ( 018 mm) bedknife movement for each position Front: Aluminum Wiehle , 2 5 ” (6 4 cm) diameter with sealed bearings and through-shaft Option between full, narrow-spaced and …..