Toro Owners Manual - Enlarge page 1 of 11
2 of 11
3 of 11
4 of 11
5 of 11
6 of 11
7 of 11
8 of 11
9 of 11
10 of 11
11 of 11
From inside (document excerpt):
Groundsmaster 7200 Series Specifications GROUNDSMASTER 7200, MODEL 30360, 30361 & 30362 Kubota®, 3-cylinder, liquid-cooled diesel, 28 bhp (21 kW), 25 hp net @ 2725 rpm, 51 ft-lb. torque @ 2100 rpm. High idle 3200 rpm (uninstalled), low idle 1600 rpm, displacement 1123cc. Remote mounted Donaldson® air filter, external spin-on oil filter and high flow fixed fan. Rear mounted, 8 fins/inch, 3 rows. 11.5 gallons (43.5 liter), diesel.
3.9 quarts (3.69 liter). 3.5 gallons (13.25 liter). Transmission directly mounted to engine via bell housing, two independent closed-loop circuits. One pump/motor controlling left ® GROUNDSMASTER 7210, MODEL 30363, 30364 &30365 Kubota®, 3-cylinder, liquid-cooled diesel turbo, 35 bhp (26 kW), 31.5 hp net @ 3000 rpm, 63 ft-lb. torque @ 2000 rpm. High idle 3220 rpm (uninstalled), low idle 1350 rpm, displacement 1123cc. Remote mounted Donaldson® air filter, external spin-on oil filter and high flow fixed fan. ENGINE RADIATOR FUEL CAPACITY ENGINE OIL W/ FILTER HYDRAULIC OIL TRANSMISSION side forward, neutral, and reverse, and one pump/motor controlling right side forward, neutral, and reverse. Pumps are variable displacement piston type with slippers and full stroke capacity of 18cc/rev. WHEEL DRIVE Independent high-torque, low-speed wheel motors with 310cc displacement. PTO CLUTCH Hydraulically actuated wet multi-disc clutch. STEERING CONTROL Adjustable twin sticks with high performance KYB® hydraulic dampers. Rev/N/Forward, located on sides of operator. (MOWING CONFIGURATION) ALTERNATOR/GENERATOR GROUND SPEED Forward 0-12.5 mph (0-20 km/h), variable. Reverse 0-8.5 mph (0-13.7 km/h), variable. 12 Volt, 40 amp internal regulated charging @ 3150 rpm. BATTERY BCI Group No.: 26, 540 cold cranking amps @ 0° F. INSTRUMENTATION Hour meter, glow indicator, high temp indicator, oil pressure indicator, alternator indicator. SAFETY LOGIC CONTROLS Toro Standard SCM. Tractor neutral, operator presence (engine shuts down if operator is not in seat and traction sticks are moved to the operation INTERLOCKS position), parking brake, PTO on, auxiliary hydraulics on, high temp (PTO shuts down but engine still running), over temp (engine shuts down). SERVICE BRAKE Twin levers with dynamic braking through hydrostatic transmission. PARKING BRAKE Hand actuated brake lever with two 10.25 ” diameter disc brakes mounted on the rear wheel motors. DRIVE TIRES 24 x12-12, 6-ply pneumatic tubeless, demountable and interchangeable. Tread “Toro Tuff Trac “. FRONT CASTOR TIRES 4-ply ribbed tread, tubeless 15 x 6-6, 20-22 psi. Two piece, high back cushion seat with drain hole, deluxe low profile suspension, adjustable for operator weight, seat back ROPS Two-post foldable style ROPS certified per OSHA 1928.52 specification. SEAT angle, seat fore/aft position, lumbar support and armrest height, retractable seat belt. STORAGE Built-in cup holder, and personal storage reached from seat. IGNITION Off/run/start, located right of operator. THROTTLE Low – high idle, located right of operator. PARKING BRAKE Off – on spring applied on, located right of operator. DECK HYDRAULIC LIFT REAR HYDRAULIC LIFT (OPTIONAL) Raise/hold/lower/float, located on right of operator. Raise/hold/lower/float. Electric switch right side of operator. Remote hydraulics selector switch, located on right console. CURB CLIMBING Capable of climbing 8 ” curbs. TIE DOWNS Four loops, one located on each corner of the machine. CERTIFICATION equipment. Cutting units sold in EU meets specifications of European standard per CE Machinery Directory EN836. WARRANTY 2-year limited warranty. Refer to the Operator’s Manual for further details. * Specifications and design subject to change without notice. Cutting unit meets specification of American National Standard ANSI B71.4-2004, Safety Specifications for commercial turf care Groundsmaster 7200 Series Specifications* (continued) GROUNDSMASTER® 7200 SERIES CUTTING DECKS HEIGHT OF CUT 1 ” – 6 ” (2.5 – 15.2 cm) adjustable in 0.25 ” (.6 cm) increments. SIDE DISCHARGE CONSTRUCTION GUARDIAN RECYCLER CONSTRUCTION ® ® 7-gauge steel 5.50 ” (13.9 cm) deep; welded deck with grass discharged on the right side. A 5/16 ” (.8 cm) thick rubber discharge chute cover discharge opening to limit the throw distance of clippings. 7-gauge steel 4.25 ” (10.8 cm) deep; welded deck equipped with special baffles which recirculate grass clippings, leaves, etc. Three deflectors inside the chamber redirect clippings that are elevated in the chambers so that they are cut and re-cut. Deck chambers prevent throwing of objects out from the deck. Splined PTO drives gearbox transferring power to three separate spindles via two separate belts. All spindles have 1.25 ” CUTTER DRIVE (3.2 cm) diameter shafts mounted in 9 ” (22.9 cm) conical housing with two greaseable tapered roller bearings. BLADES Three, .25 ” (.6 cm) thick, 2.5 ” (6.3 cm) wide, heat-treated steel blades. two torsion springs counterbalances some cutting deck weight to reduce turf damage. Rigid front frame which support deck via 4 vertically suspended chains. Front drag links provide fore/aft and left/right stability. DECK SUSPENSION Hydraulic deck lift with load holding check valves and gravity lower is standard component. Weight transfer system consisting of BELT IDLER Spring loaded (torsion) idler. DECK SKID deck. Replaceable, bolt-on, non-marking polymeric skid on both sides for Guardian® Recycler deck and on left side on side discharge ANTI-SCALP CUPS Anti-scalp cup located on each blade spindle. CUTTING DECK CONFIGURATIONS 62 ” GUARDIAN® RECYCLER® 62 ” (158 cm) 16,000±1,000 ft./min. NA 4.25 ” (10.8 cm) 4 2 NA NA * Only certain models will meet CE noise specifications 72 ” GUARDIAN® RECYCLER® 72 ” (182.8 cm) 16,000±1,000 ft./min. NA 4.25 ” (10.8 cm) 6 2 NA NA 72 ” SIDE DISCHARGE* 72 ” (182.8 cm) 18,000±1,000 ft./min. Yes 5.5 ” (13.9 cm) 6 1 Yes Yes WIDTH OF CUT BLADE TIP SPEED (AT 3250 ENGINE RPM) 5/16 ” THICK RUBBER DISCHARGE CHUTE CUTTING DECK DEPTH DECK ANTI-SC