Husqvarna 323P4 325P5 X-Series Chainsaw Owners Manual, 2003

Operator’s manual (EPA) 323P4 325P5X-series Please read the operator’s manual carefully and make sure you understand the instructions before using the machine. English KEY TO SYMBOLS Symbols WARNING! The machine can be a dangerous tool if used incorrectly or carelessly, which can cause serious or fatal injury to the operator or others. Please read the operator’s manual carefully and make sure you understand the instructions before using the machine. Always wear: A protective helmet where there is a risk of falling objects Approved hearing protection Protective goggles or a visor Protective goggles or a visor must be worn.

Visual check. Other symbols/decals on the machine refer to special certification requirements for certain markets. Switch off the engine by moving the stop switch to the STOP position before carrying out any checks or maintenance. Always wear approved protective gloves. Regular cleaning is required. This machine is not electrically insulated. If the machine touches or comes close to high-voltage power lines it could lead to death or serious bodily injury. Electricity can jump from one point to another by arcing. The higher the voltage, the greater the distance electricity can jump. Electricity can also travel through branches and other objects, especially if they are wet. Always keep a distance of at least 10 m between the machine and high-voltage power lines and/or any objects that are touching them. If have to work within this safe distance you should always contact the relevant power company to make sure the power is switched off before you start work. This machine has a long reach. Make sure that no people or animals come closer than 15 m when the machine is running. Always wear approved protective gloves. Filling with chain oil and adjusting oil flow Wear sturdy, non-slip boots. 2 ­ English CONTENTS Contents KEY TO SYMBOLS Symbols . CONTENTS Contents Note the following before starting: SAFETY INSTRUCTIONS Personal protective equipment . Machines safety equipment Checking, maintaining and servicing the machines safety equipment General safety precautions Safety instructions for using a pruning saw . WHAT IS WHAT? What is what? ASSEMBLY Fitting the cutting head Fitting the bar and chain Adjusting the harness Filling with oil Assembling and dismantling the two-piece shaft (325P5) . FUEL HANDLING Fuel Fuelling STARTING AND STOPPING Check before starting . Starting and stopping . MAINTENANCE Carburettor . Muffler Cooling system Spark plug Air filter . Bevel gear Maintenance schedule . TECHNICAL DATA Technical data FEDERAL EMISSION CONTROL WARRANTY STATEMENT YOUR WARRANTY RIGHTS AND OBLIGATIONS . Note the following before starting: ! WARNING! Under no circumstances may the design of the machine be modified without the permission of the manufacturer. Always use genuine accessories. Non-authorized modifications and/or accessories can result in serious personal injury or the death of the operator or others. Your warranty does not cover damage or liability caused by the use of non-authorized accessories or replacement parts. The machine is only designed for cutting branches and twigs. Maintenance, replacement, or repair of the emission control devices and system may be performed by any nonroad engine repair establishment or individual. Husqvarna AB has a policy of continuous product development and therefore reserves the right to modify the design and appearance of products without prior notice. This decal certifies that the product has been approved in accordance with American exhaust emissions requirements EPA Ph II and CARB Tier II. The Emissions Compliance Period referred to on the Emissions Compliance label indicates the numbers of operating hours for which the engine has been shown to meet Federal and California emission requirements. HUSQVARNA AB HUSKVARNA SWEDEN IMPORTANT ENGINE INFORMATION TWC THIS ENGINE CONFORMS TO U.S. EP A PH1 FOR SMALL NON – ROAD ENGINES. REFER TO OPERATOR`S MANUAL FOR MAINTENANCE SPECIFICATIONS AND ADJUSTMENTS. 26 English ­3 SAFETY INSTRUCTIONS Personal protective equipment IMPORTANT INFORMATION The machine can be a dangerous tool if used incorrectly or carelessly, which can cause serious or fatal injury to the operator or others. Please read the operator’s manual carefully and make sure you understand the instructions before using the machine. You must wear approved protective equipment whenever you use the machine. Personal protective equipment cannot eliminate the risk of injury but it will reduce the degree of injury if an accident does happen. Ask your dealer for help in choosing the right equipment. Machines safety equipment This section describes the machines safety equipment, its purpose, and how checks and maintenance should be carried out to ensure that it operates correctly. See the “What is what? ” section to locate where this equipment is positioned on your machine. WARNING! Never use a machine that has faulty safety equipment! Carry out the inspection, maintenance and service routines listed in this section. ! ! GLOVES WARNING! Remove your hearing protection as soon as you stop the engine, so that you can hear any noises or warning signals.

Wikipedia’s page for Husqvarna

Publisher: www.husqvarna.com