Toro Owners Manual, 2006 - Enlarge page 1 of 40
2 of 40
3 of 40
4 of 40
5 of 40
6 of 40
7 of 40
8 of 40
9 of 40
10 of 40
11 of 40
12 of 40
13 of 40
14 of 40
15 of 40
16 of 40
17 of 40
18 of 40
19 of 40
20 of 40
21 of 40
22 of 40
23 of 40
24 of 40
25 of 40
26 of 40
27 of 40
28 of 40
29 of 40
30 of 40
31 of 40
32 of 40
33 of 40
34 of 40
35 of 40
36 of 40
37 of 40
38 of 40
39 of 40
40 of 40
From inside (document excerpt):
Form No. 3356-377 Rev A Greensmaster® Flex 18 Walk-Behind Mower Model No. 04018 (Traction Unit)–Serial No. 260000001 and Up Model No. 04206 (Cutting Unit)–Serial No. 260000001 and Up Register your product at www.Toro.com Original Instructions (EN) Warning CALIFORNIA Proposition 65 Warning The engine exhaust from this product contains chemicals known to the State of California to cause cancer, birth defects, or other reproductive harm. This spark ignition system complies with Canadian ICES-002 Model No.
Serial No. Introduction Read this information carefully to learn how to operate and maintain your product properly and to avoid injury and product damage. You are responsible for operating the product properly and safely. You may contact Toro directly at www.Toro.com for product and accessory information, help finding a dealer, or to register your product. Whenever you need service, genuine Toro parts, or additional information, contact an Authorized Service Dealer or Toro Customer Service and have the model and serial numbers of your product ready. Figure 1 and Figure 2 identify the location of the model and serial numbers on the product. Write the numbers in the space provided. Figure 2 1. Location of the model and serial numbers-Cutting Unit Cutting unit: Model No. Serial No. This manual identifies potential hazards and has safety messages identified by the safety alert symbol (Figure 3), which signals a hazard that may cause serious injury or death if you do not follow the recommended precautions. Figure 3 1. Safety alert symbol. This manual uses two other words to highlight information. Important calls attention to special mechanical information and Note emphasizes general information worthy of special attention. Figure 1 1. Location of the model and serial numbers-Traction unit Contents Introduction . 2 Safety 4 Safe Operating Practices 4 Toro Mower Safety 6 2 Contact us at www.Toro.com. Printed in the USA. Traction unit: 2006–The Toro® Company 8111 Lyndale Avenue South Bloomington, MN 55420 Sound Pressure 7 Sound Power . 7 Vibration . 7 Safety and Instructional Decals 7 Setup 10 1 Installing the Handle . 10 2 Installing the Kickstand . 11 3 Adjusting the Handle 12 4 Installing the Transport Wheels 12 5 Checking Fluid Levels . 13 6 Installing the Grass Basket . 13 7 Reading the Manuals and Viewing the Video . 13 Product Overview . 15 Controls . 15 Specifications . 16 Operation 18 Think Safety First 18 Checking the Engine Oil Level . 18 Filling the Fuel Tank 18 Checking the Interlock Switch Operation 19 Starting and Stopping the Engine 20 Transport Operation . 20 Preparing to Mow 20 Mowing Operation 20 Maintenance 22 Recommended Maintenance Schedule(s) . 22 Daily Maintenance Checklist 23 Engine Maintenance 24 Engine Oil . 24 Servicing the Air Cleaner . 24 Replacing the Spark Plug 25 Fuel System Maintenance 26 Cleaning the Fuel Filter 26 Electrical System Maintenance . 26 Servicing the Interlock Switch . 26 Drive System Maintenance . 27 Checking the Transmission Fluid Level . 27 Changing the Transmission Fluid . 27 Brake Maintenance 28 Adjusting the Service/Parking Brake . 28 Belt Maintenance . 28 Adjusting the Belts 28 Controls System Maintenance 31 Adjusting the Traction Control . 31 Adjusting the Reel Control . 31 Cutting Unit Maintenance 32 Separating the Cutting Unit from the Traction Unit . 32 Adjusting the Rear Roller . 32 Adjusting the Bedknife to the Reel . 33 Adjusting the Height of Cut . 34 Adjusting the Cut-Off Bar 35 Setting the Machine to Match Turf Conditions 36 Servicing the Bedbar 37 Backlapping the Reel 38 Storage 39 3 Safety This machine meets or exceeds CEN standard EN 836:1997, ISO standard 5395:1990, and ANSI B71.4-1999 specifications in effect at the time of production when the Operator Presence Kit, Part No. 105-5333 is installed. Improper use or maintenance by the operator or owner can result in injury. To reduce the potential for injury, comply with these safety instructions and always pay attention to the safety alert symbol, which means CAUTION, WARNING, or DANGER- “personal safety instruction. ” Failure to comply with the instruction may result in personal injury or death. Safe Operating Practices The following instructions are from the CEN standard EN 836:1997, ISO standard 5395:1990, and ANSI B71.4-1999. Training · Read the Operator’s Manual and other training material carefully. Be familiar with the controls, safety signs, and the proper use of the equipment. · Never allow children or people unfamiliar with these instructions to use or service the mower. Local regulations may restrict the age of the operator. · Never mow while people, especially children, or pets are nearby. · Keep in mind that the operator or user is responsible for accidents or hazards occurring to other people or their property. · The owner/user can prevent and is responsible for accidents or injuries occurring to himself or herself, other people, or property. Preparation · While mowing, always wear substantial footwear, long trousers, hard hat, safety glasses, and ear protection. Long hair, loose clothing, or jewelry may get tangled in moving parts. Do not operate the equipment when barefoot or wearing open sandals. · Thoroughly inspect the area where the equipment is to be used and remove all objects which may be thrown by the machine. · Warning-Fuel is highly flammable. Take the following precautions: Store fuel in containers specifically designed for this purpose. Refuel outdoors only and do not smoke while refuelling. Add fuel before starting the engine. Never remove the cap of the fuel tank or add fuel while the engine is running or when the engine is hot. If fuel is spilled, do not attempt to start the engine but move the machine away from the area of spillage and avoid creating any source of ignition until fuel vapors have dissipated. Replace all fuel tanks and container caps securely. · Replace faulty silencers. · Evaluate the terrain to determine what accessories and attachments are needed to properly and safely perform the job. Only use accessories and attachments approved by the manufacturer. · Check that operator’s presence controls, safety switches and shields are attached and functioning properly. Do not operate unless they are functioning properly. Operation · Do not operate the engine in a confined space where dangerous carbon monoxide fumes can collect. · Mow only in daylight or in good artificial light. · Before attempting to start the engine, disengage all blade attachment clutches, shift into neutral, and engage the parking brake. · Do not use on slopes of more than 15°.
Wikipedia’s page for Toro Company
Company Web Site: www.toro.com