MTD 313-205 313-230 20-Inch Snow Blower Owners Owners Manual - English

III · I Model Nos. 3-13-205 & 313-230 20 ” SNOW THROWER For one year from date of purchase, MTD Products Inc, will replace for the original purchaser, free of charge, F.O.B. factory or authorized service firm, any part or parts found to be defective in material or workmanship; All transportation · 1. Know the controls and how to stop quickly-READ THE OWNER’S MANUAL. 2. Disengage power and stop motor before cleaning discharge, removing obstacles, making adjustments, or when leaving operation position.

Snow Blower and Snow Thrower User Manual Free Download. Snow Removal Operator’s Manual. Free Manual Download PDF.

3. Never direct discharge at bystanders nor allow anyone in front of machine-debris may be hidden in the snow. 4. Keep children and pets a safe distance away. 5. Do not allow children to operate machine nor allow adults to operate it without proper instruction. 6. Adjust height to clear gravel or crushed rock surface. 7. Exercise caution to avoid slipping or falling, especi when operating in reverse. 8. Handle gasoline with care – it is highly flammable. A. Use approved gasoline container: B. Never add gasoline to a running motor – fill tank out of doors and wipe up spilled gasoline. C. Replace gasoline cap securely. D. Open door fif motor i!> run in garage – exhaust gases are dangerous. 9. Disengage all clutches and shift into neutral before starting motor. Keep hands, feet and clothing away from power drh,en parts. 10. Use a grounded three wire extension cord for all plugin electric units. 11. Keep machine in good operating condition and keep safety devices in place. charges on parts submitted for replacement under this warranty must be paid by the purchaser. This warranty does not include replacement of parts which become inoperative through misuse, excessive use, accident, neglect, improper maintenance or alterations by unauthorized persons. This warranty does not include the engine, motor, battery, battery charger or any component parts thereof. For service on these units refer to the applicable manufacturer’s warranty. The above warranty will apply only to the original owner and will be effective only if the warranty card has been properly processed. It will not apply where the unit has been used commercially. Warranty service is available through your local authorized service dealer or distributor. UNDER NO CIRCUMSTANCES WILL THE RETURN OF A COMPLETE UNIT BE ACCEPTED BY THE FACTORY UNLESS PRIOR WRITTEN PERMISSION HAS BEEN EXTENDED. M TD ROD U CT. INC · 5389 WEST 130th STREET · P. O. BOX 2741 CLEVELAND OHIO 44111 FORM NO. 770-4790 ASSEMBLY INSTRUCTIONS 4. Chute Crank. Assemble the chute crank (two parts) into the two holes in the handle panel being sure the rod passes through the chute control bracket. Push the rod all the way through and assemble it to the chute bracket with two cotter pins and flat washers. 5. Remove the wing nut, washer, and carriage bolt 5/16-18 x % Ig. from the chute assembly. lift the deflector and reassemble. If the deflector will not move, loosen the screw and nut slightly so it pivots freely. Right hand (R.H.) and left hand (L.H.) are as observed from the operating position. 1. Assemble chrome handles (Ref. No. 24 and 29) to the frame with four hex head cap screws %-16 x % long and four lock washers % “. DO NOT TIGHTEN. 2. Assemble handle panel (Ref. No. 20) to the handles with the four carriage bolts 1,4-20 x 1Y2 Ig. and hex locknuts 1,4-20 thd. Assemble handle panel so you can read the instructions on the handle panel from the operating position. LIFT HANDLE UP AS YOU TIGHTEN ALL BOLTS AND NUTS ON THE HANDLE ASSEMBLY. NOTE: Model 313-205 has no Reverse. 3. The linkage arm (Ref. No. 21) for the transmission is located on the R.H. side of the frame.

Wikipedia’s page for MTD Products

Publisher: www.mtdproducts.com