Toro Owners Manual - Enlarge page 1 
From inside (document excerpt):
eelmaster 3100-D Specifications* ® REELMASTER 3100-D, MODEL 03170 ENGINE CONFIGURATION FUEL CAPACITY TRACTION DRIVE GROUND SPEED CONTROLS GAUGES ELECTRICAL & INTERLOCKS TIRES FRAME BRAKES STEERING OVERALL DIMENSIONS CUTTING UNIT CONFIGURATION CUTTING UNIT OFFSET CERTIFICATION WARRANTY ® REELMASTER 3100-D, MODEL 03171 w/SIDEWINDER Kubota liquid-cooled diesel, 3-cylinder, 21 5 hp (16 kW) net @ 2500 RPM 68 5 cu in (1123 cm3) displacement Pressurized lubrication system with 3 5 U S qt (3 3 liter) capacity Heavy duty, radial seal air cleaner Fuel/water separator with visible bowl Rear mounted engine, front operator position Rear mounted radiator Two post ROPS and seat belt standard 7 5 gallons (28 liters) 2008 models Biodiesel-Ready for use up to B-20 (20% biodiesel and 80% petrol blend) Series/Parallel hydraulic traction circuit provides continuous 3-wheel drive, in mow and transport Hydrostatic traction drive provides infinitely variable speed in forward and reverse 6 gallon (23 liter) hydraulic system capacity Mow: 0-6 mph (0-10 km/h); Transport: 0-9 mph (0-14 km/h) Reverse: 0-4 mph (0-6 km/h) Forward and reverse traction control pedals, mow/transport lever, hand activated park brake, ignition key switch, tilt steering wheel lock, PTO switch, throttle, joystick control for cutting unit raise and lower (and for moving cutting units side-to-side on Sidewinder equipped models), cutting unit transport lock, reel speed and backlap control knob Hour meter, fuel gauge, cluster gauge with glow plug and charge indicator lights, and low engine oil pressure and high coolant temperature warning lights (high temperature safety shut off) 12-volt, 585 cold cranking amps at 0° F (-18° C), 40 amps with regulator/rectifier Traction pedal, operator presence in seat, PTO engage or disengage, and cutting unit mow or transport safety interlock switches Front: 20 x 10-12, 4-ply Turf Trac Rear: 20 x 12-10 Formed steel, welded steel and steel tubing Hydrostatic service brake, parking brake Power steering with tilt steering wheel Track Width: Wheel Base: Overall Length: Fixed position cutting units 3 ” (7 6 cm) in 72 ” (183 cm) width of cut 10 ” (25 cm) in 85 ” (216 cm) width of cut 55 ” (140 cm) 56 ” (142 cm) 93 ” (248 cm) Overall Height: Transport Width: Approx Weight with Cutting units: 71 ” (180 cm) with ROPS 80 ” (203 cm) in 72 ” (183 cm) woc 92 ” (234 cm) in 85 ” (216 cm) woc 1860 lbs (844 kg) Operator controlled moveable cutting units travel ±12 ” (30 cm) left or right from center; total of 24 ” (61 cm) of infinite variability Maximum 15 ” (38 cm) in 72 ” (183 cm) width of cut Maximum 22 ” (56 cm) in 85 ” (216 cm) width of cut This product complies with the American National Standards Institute (ANSI B71-4 1999) and European Community specifications (CE Certified) Two-year limited warranty, refer to operators manual for details CUTTING UNITS TYPE REEL BLADE OPTIONS HOC RANGE CUTTING WIDTH CLIP FREqUENCY/ BACKLAPPING BEDKNIFE TO REEL ADjUSTMENT ROLLERS Three hydraulically-driven, balanced, 7 ” (17 8 cm) diameter reels Cutting units interchangeable to all three positions 5, 8, and 11-blade reels available for 27 ” (68 6 cm) cutting unit 5 and 8 blade reels available for 32 ” (81 3 cm) cutting unit Height of cut ranges 25 ” to 2 ” ( 63 – 5 1 cm) standard in floating position, 1 5 ” to 2 5 ” (3 8 – 6 4 cm) in fixed position 72 ” (183 cm), or 85 ” (216 cm) width of cut dependent on cutting unit selection Manually controlled variable reel speed for adjustment of clip frequency Standard on-board backlapping Dual point adjustment (DPA) of bedknife to reel Full roller standard on rear of cutting unit and plastic front Wiehle roller SUNSHADE BIMINI CANVAS Model 30358 *Specifications and design subject to change without notice The Reelmaster 3100-D is manufactured in Tomah, WI ISO 9002 Certified Plant 51 .